Codes, permits and design review
Permits And Approvals For Built-In Cabinetry | The Code Position, With Citations
Cabinetry and finish work are exempt from building permits by name in both states. Electrical, plumbing and structural work are not. This page sets out the detail with the code sections, so you can check it rather than take anyone's word for it.
10 years and 1,310-plus clients means we have dealt with a lot of building departments. Cabinetry itself is permit-exempt in both states; where your scope reaches electrical or structural work we name the licensed trade separately in your written price.
Get Your Custom Built-In Quote
Tell us the room and we will come and measure it. No charge for the visit or the drawings.
The permit position for built-in cabinetry, with citations
This page sets out the permit position for built-in cabinetry across the jurisdictions we work in, with the code sections cited. It is written so you can check it rather than take our word for it.
We build cabinetry and finish work without a building permit in either state, because both codes exempt it by name. We do pull permits, through licensed trades, for electrical, plumbing and structural alteration. We file with whichever city or township runs its own building department.
| Jurisdiction | Cabinetry exempt? | Citation |
|---|---|---|
| Ohio, statewide | Yes, by name | Residential Code of Ohio section 102.10 exempts painting, tiling, carpeting, cabinets, countertops and similar finish work. |
| City of Dayton | Yes, stated plainly | Dayton building division guidance states permits are not needed for painting, papering, tiling, carpeting, cabinets or countertops. |
| Kentucky, statewide | Yes, by name | Kentucky Residential Code R105.2, Building item 6, exempts finish work including cabinets and countertops. Kentucky is a statewide code state. |
| Louisville Metro | Yes, including replacement | Cosmetic interior finish work including cabinets and countertops is exempt; cabinet replacement is specifically exempt. |
| Electrical, both states | No | New circuits, receptacles and hardwired lighting require a permit and a licensed electrician. Kentucky exempts only work under 25 volts and 50 watts. |
| Structural alteration | No | Removing or altering a load-bearing wall, beam or framing is not finish work and requires a permit in every jurisdiction we serve. |
Clearances and code provisions that shape what we draw
We draw every built-in against four code provisions before we discuss finish or style, and we set them out below with the sections cited.
In practice, what pulls a built-in job into permit territory is almost never the cabinetry. It is the thing someone wants added to the cabinetry. Puck lights, strip lighting under a shelf and a switch on the wall are a new branch circuit, and that is electrical work on a permit with a licensed electrician. A receptacle inside a media cabinet is the same. Low-voltage lighting driven from a plug-in transformer usually is not, which is why we reach for it first when a client wants lit shelves and would rather not open a permit. A wet bar sink behind a bourbon display is plumbing. Pulling out a wall to widen an opening for a wall unit is structural. We price those as separate trades and say so at quote stage, because finding out mid-job that the lighting you assumed was included needs an electrician and an inspection is the single most common unpleasant surprise on this kind of work.
- Fireplace clearance to combustibles
- We hold International Residential Code R1001.11: nothing combustible within six inches of a masonry firebox opening; projection limited to one eighth of an inch per inch of distance between six and twelve inches; a mantel projecting two inches or more at least twelve inches above the opening. We follow the listing on factory-built and gas units.
- Working space at an electrical panel
- We keep the working space National Electrical Code article 110.26 requires, roughly thirty inches wide, thirty-six inches deep and seventy-eight inches high in front of a panel. We build no cabinetry into it and store nothing there.
- Emergency escape and rescue openings
- We work to International Residential Code section R310 and build nothing across an egress opening or the route to it in a basement bedroom or habitable space.
- Habitable ceiling height
- We hold IRC R305 heights: seven feet for habitable spaces, hallways and basements with habitable space, six feet eight inches for bathrooms and laundry. We draw around beams and ducts.
Permit questions we are asked most often
Do I need a permit for built-in cabinetry in Ohio?
Generally no for the cabinetry itself. The Residential Code of Ohio exempts finish work, naming painting, tiling, carpeting, cabinets and countertops, at section 102.10. The City of Dayton states the same thing in plain terms on its own guidance. What is not exempt is structural alteration, new electrical and new plumbing.
Do I need a permit for built-in cabinetry in Kentucky?
Generally no for the cabinetry itself. The Kentucky Residential Code exempts finish work at R105.2, Building item 6, naming painting, papering, tiling, carpeting, cabinets, countertops and similar work. Kentucky is a statewide code state, so that exemption applies across every Kentucky city we serve. Electrical, plumbing and structural work are separate.
When does a built-in project need a permit?
When it stops being finish work. Removing or altering a load-bearing wall, beam or framing needs a permit. So does any new electrical circuit, outlet or hardwired light, and any plumbing. Finishing a basement as habitable space brings its own requirements around egress and ceiling height.
Is shelving exempt from permits?
Shelving is not named in either state's exemption list and it is not named in any requires-a-permit list either. It is almost certainly covered by the phrase 'and similar work' in both codes, but that is an inference rather than a published ruling, so we confirm it with the authority having jurisdiction rather than asserting it.
Does a Murphy bed need a permit?
We do not publish an answer to this because no code provision or authoritative guidance was found for any of our jurisdictions. The defensible position is that non-structural furniture installation generally falls under finish work, but a wall bed anchored into framing, or any accompanying electrical, may be treated differently. We ask the authority having jurisdiction for your address.
Who pulls the permit for electrical work inside cabinetry?
The licensed electrician does, and their work is named separately in your written scope as theirs. In Kentucky the licensing exemptions are narrow: only low-voltage work under 25 volts and 50 watts sits outside them, which is where some LED strip lighting on a listed driver can fall. A new 120 volt fixture or receptacle does not.
Does historic district designation mean I need approval for interior work?
In most of this metro, no. The City of Cincinnati states that interior work requires no Certificate of Appropriateness where it has no exterior impact, with five named exceptions citywide, none residential. Covington and Newport both publish explicit interior exemptions. Bellevue publishes an exterior scope and no interior exemption, so there we confirm with the city first.
Which local authorities run their own building departments here?
Several, and it changes the paperwork rather than the rules. Norwood is an independent municipality and a full enclave inside Cincinnati with its own building department. Madeira, Montgomery, Blue Ash, Indian Hill and Harrison are separate cities, as is every Kentucky city we serve. Townships such as Anderson, Colerain, Green, Delhi, Symmes, West Chester and Liberty route differently again.
Back to the main site
This page exists so the code position is written down and checkable. If you want to see what we actually build and where, the main site covers it.